Hydrocarbon Compression

Archive for the ‘Gas Turbine’ tag

Gas Turbine Air Compressor Problems

without comments

One way of looking at a gas turbine centrifugal compressor is that the combustion air compressor must pump sufficient air to support combustion across the turbine blades as needed to spin the gas compressor at its required speed. Any factors which reduce the flow delivered by the combustion air compressor will reduce horsepower available to the gas compressor. The factors which reduce air flow are identical to those parameters which reduce the capacity of any centrifugal compressor:

• High suction temperatures due to elevated ambient temperature.
• Mechanical damage.
• Low suction pressure due to plugging of the air filter suction screen. A pressure drop of 4 inches of water will reduce the air compressor capacity by roughly 2%
• Dirt accumulation in the rotors internals due to inadequate suction filtration and dusty air.
• Slow speed due to the problems listed above with the gas turbine driver.

To remove dirt and dust accumulations from the air compressor rotor, detergent water washing is required. An aqueous detergent solution is squirted into doors provided on the air intake ducting. The machine is running at a reduced speed during this period, and the natural gas process piping is isolated from the compressor. In addition to washing the air compressor rotor, some of the detergent solution may carry-over to the turbine blades and promote some cleaning. During detergent washing, the turbine is powered in the normal fashion—i.e. by firing natural gas.

Frequent cleaning or replacement of the air intake filters will also improve air flow availability for combustion. To simplify this procedure, a so called “Huff & Puff’, self-cleaning air filter may be retrofitted into existing equipment. Such a self-cleaning filter should operate for two years without manual maintenance. Also, it reportedly reduces air filter pressure drop by an average of five inches of water over this two year period for an effective increase in engine horsepower availability of 2-3%.

The combustion air compressor should develop a certain discharge pressure (110 PSIG is typical) as specified by the manufacturer’s data. After correcting for suction pressure, suction temperature and speed, (see manufacturer’s correlations), if the indicated air discharge pressure cannot be achieved, the combustion air compressor should be washed. If washing fails to correct the shortcoming, the rotor should be checked for mechanical damage.

Keep in mind that not only will problems connected with the turbine blades slow down the combustion air compressor, but that deficiencies with the combustion air compressor will indirectly be reflected in lower combustion air compressor speed.

Written by Jack

January 30th, 2010 at 1:02 pm

Posted in Gas Turbine

Tagged with ,

Gas Turbine Exhaust Temperature Unit Troubleshooting

without comments

Gas turbines are limited, as are all rotating assemblies, by either speed or power. For an electric motor, the power limit is manifested by maximum amperage, (more precisely, the maximum permissible winding temperature). The situation with gas turbines is similar. The ultimate amount of power (i.e. work, horsepower), that can be developed by the turbine blades, is limited by the turbine exhaust temperature.

A typical maximum turbine exhaust temperature is 1,100°F. This limit is imposed by the metallurgy of the turbine’s blades. Continuous operation above the turbines design exhaust temperature will lead to accelerated deterioration of the blades and a consequent reduction in engine horsepower.

When neither end of the centrifugal compressor is running at its peak speed, and the turbine exhaust temperature is below it’s design limit, there are two other possibilities which may be limiting horsepower output:

• Fuel gas firing is limited by a faulty over-ride on the temperature controller. That is, the exhaust temperature is artifically surpressed by an instrument malfunction.
• The fuel gas flow control valve is wide open; or it is partially plugged by natural gas hydrates.

When the turbine exhaust temperature is at it’s limit, and horsepower output is deficient, other possible causes are:

• Excessive wear to turbine blades.
• Air/fuel ratio problems.
• Carbon deposits on turbine blades. Periodic detergent washing of the combustion air compressor will help reduce this effect.
• Lack of proper flow from the combustion compressor.

Written by Jack

January 30th, 2010 at 12:32 pm

Gas Turbine Driven Centrifugal Compressors

without comments

While the majority of natural gas field and transmission compressors are reciprocating machines, a sizable minority are centrifugal compressors driven by gas turbines. Only on rare occasions can electric, steam or deisel oil drives compete with natural gas as compressor fuel in pipeline service.

A gas turbine works on the same principle as a jet engine. Air is compressed (typically to 110 PSIG), and discharged into a combustion zone. Fuel gas is also injected into the combustion zone. The pressurized, burning gas expands as it passes across the blades of a turbine. The turbine serves two functions:

• One or more wheels of the turbine drives the combustion air compressor.
• One or more wheels of the turbine drives the gas compressor.

The major part of the horsepower developed in a gas turbine is consumed by the combustion air compressor. The gas compressor absorbs about one third of the gas turbines power output. Work done by the combustion air compressors is recycled back to the turbine blades via the pressurized combustion air.

An important feature of the gas turbine driven compressor is that the two ends of the machine are not mechanically coupled. This is called a split shaft design; which means that the combustion air compressor and the gas compressor operate at different speeds. This permits the air compressor end to run at a speed consistant with developing full horsepower, while the gas compressor end may be running at a lower speed due to factors such as high discharge pressure.

Written by Jack

January 27th, 2010 at 8:12 pm